Fiat Ducato L3H2 vs L4H2
The L4H2 is 365 mm1 ft 2 in longer than the L3H2, and the same height and width. The L4H2 has 365 mm1 ft 2 in more load length at the floor and the same wheelbase.
VanCAD models the Fiat Ducato in 7 sizes (L1H1, L2H1, L2H2, L3H2, L3H3, L4H2, L4H3), from 4,963 mm16 ft 3 in to 6,363 mm20 ft 11 in long and 2,254 mm7 ft 5 in to 2,760 mm9 ft 1 in tall, with front-wheel drive. The Fiat Ducato is also sold as the Peugeot Boxer, the Citroën Relay, the Citroën Jumper, the RAM Promaster, the Toyota Proace Max, the Vauxhall Movano (2021 on) and the Opel Movano (2021 on).
These are two sizes of the same van, the Fiat Ducato.
Side profiles at one scale
- Fiat Ducato L3H2
- Fiat Ducato L4H2
- Both
Lined up at the rear doors. The drawings leave off the rear bumper, so this is the line the load space ends at.
Drawn from VanCAD's 3D models at one scale, with the ground lines level. The figures in the table are the manufacturers' published ones: read a measurement from the table, not the picture.
The published figures
| Measurement | Fiat Ducato L3H2 | Fiat Ducato L4H2 | Difference |
|---|---|---|---|
| Overall length | 5,998 mm19 ft 8 in | 6,363 mm20 ft 11 in | 365 mm longer1 ft 2 in longer |
| Overall width (excluding mirrors) | 2,050 mm6 ft 9 in | 2,050 mm6 ft 9 in | SameSame |
| Overall height | 2,522 mm8 ft 3 in | 2,522 mm8 ft 3 in | SameSame |
| Wheelbase | 4,035 mm13 ft 3 in | 4,035 mm13 ft 3 in | SameSame |
| Rear overhang | 1,015 mm3 ft 4 in | 1,380 mm4 ft 6 in | 365 mm longer1 ft 2 in longer |
| Ground clearance | 165 mm0 ft 6 in | 165 mm0 ft 6 in | SameSame |
| Side door opening | 1,250 mm4 ft 1 in | 1,250 mm4 ft 1 in | SameSame |
| Load length at floor | 3,705 mm12 ft 2 in | 4,070 mm13 ft 4 in | 365 mm longer1 ft 2 in longer |
| Maximum internal load width | 1,870 mm6 ft 2 in | 1,870 mm6 ft 2 in | SameSame |
| Maximum internal load height | 1,932 mm6 ft 4 in | 1,932 mm6 ft 4 in | SameSame |
| Load floor height | 550 mm1 ft 10 in | 550 mm1 ft 10 in | SameSame |
| Kerb weight (approximate) | 2,095 kg4,619 lb | 2,235 kg4,927 lb | 140 kg heavier308 lb heavier |
| Gross vehicle weight (example rating) | 3,500 kg7,716 lb | 3,500 kg7,716 lb | SameSame |
| Payload (approximate) | 1,405 kg3,097 lb | 1,265 kg2,789 lb | 140 kg less308 lb less |
| Drive | Front-wheel driveFront-wheel drive | Front-wheel driveFront-wheel drive | SameSame |
| Design this van | Design this van |
The difference column reads the Fiat Ducato L4H2 against the Fiat Ducato L3H2: "longer" means the Fiat Ducato L4H2 is the longer of the two.
More comparisons
Other comparisons with the Fiat Ducato.
- Fiat Ducato vs Mercedes-Benz Sprinter
- Fiat Ducato vs Ford Transit
- Fiat Ducato vs Renault Master
- Fiat Ducato vs Volkswagen Crafter
- Fiat Ducato vs Iveco Daily
- Fiat Ducato vs Vauxhall Movano (pre-2021)
- Fiat Ducato vs Opel Movano (pre-2021)
- Fiat Ducato vs Nissan NV400
- Fiat Ducato vs Nissan Interstar
- Fiat Ducato vs MAN TGE
- Fiat Talento vs Fiat Ducato
- Fiat Ducato L2H2 vs L3H2
How to read these figures
Kerb weight (curb weight in North America) is the unladen mass in running order (all fluids, a 90% full fuel tank and a 75 kg driver), for a base-specification panel van. It is researched and approximate: a real van with options fitted will weigh more, and VanCAD lets you edit the figure on your own design.
Gross vehicle weight is the maximum permitted total weight of the loaded van. Approximate payload is the example gross weight shown above minus our researched kerb weight. The kerb weight already includes a 75 kg driver. The remaining allowance covers the conversion, other occupants, water and luggage, plus any driver weight above 75 kg. Weight ratings, engines and options vary; check your own vehicle's weight plate and axle limits. A converted van's real remaining allowance comes from a weighbridge, weighed ready to travel.
Load length is the manufacturer's published floor length behind the bulkhead, measured at floor level in the bare van. Lining, battens and a false floor all take from it, and the figure says nothing about the height or width available above it.
Interior figures are the manufacturer's published load length at floor, maximum internal load width and maximum internal load height, where available. These are before conversion: lining, insulation and flooring reduce usable space, and maximum dimensions do not apply everywhere inside the van. Check your own vehicle before cutting or building. VanCAD's traced interior shapes are illustrative and are never used as published measurements.
VanCAD models the mainstream panel van bodies and drive layouts for each van, not every factory option. A maker may also sell four-wheel-drive, chassis-cab or crew-van versions that are not listed here, so anything on this page about which layouts a van comes in describes the versions VanCAD offers rather than the maker's full range.
Will your layout fit?
Open either van in the browser, place a bed, a kitchen and a shower at real millimetre sizes, and read back the weight you have added. Free, with no install.